|
|
|
September 5th, 2009, 22:06
|
#46 |
|
Hey Maniac...the deal was "NO PICS" until I posted my PTW & GBBR builds with the B.A.D levers first !!! I finally got mine today...just you wait!
__________________
Kevorkian  I SUPPORT THE USE OF SILICA BB BASTARDS! |
|
|
|
September 10th, 2009, 18:55
|
#47 |
|
Added a Madbull RIS Fixer/Rail Riser....the Madbull Noveske rail barrel nut when fully torqued is just a tad off in its clocking....regardless how many or little shims I add to the barrel....
The mount works fine with either sight, though I think the Aimpoint looks somehow more bulky than before on it...it also changes how the Aimpoint cowitness to the BUIS, before it was more of a 1/2 to 2/3 Cowitness, now its more like a lower 1/4... Larue Pride Fowler Irondot   Aimpoint Comp M3L+ Larue LT152  
|
|
|
|
|
September 10th, 2009, 19:03
|
#48 | |
|
Wow...looks very sexy
__________________
 Quote:
|
|
|
|
|
|
September 10th, 2009, 19:09
|
#49 |
|
|
It still looks B.A.D.
__________________
Kevorkian I SUPPORT THE USE OF SILICA BB BASTARDS! |
|
|
|
|
September 10th, 2009, 19:14
|
#50 |
|
Wow that looks awesome.. drool :roll:
|
|
|
|
|
September 16th, 2009, 21:54
|
#51 |
|
|
did some minor decoration to the 16" upper...added a mock Airsoft Surgeon gas piston...also added the offset flashlight mount to the CQB upper...
 
|
|
|
|
|
October 2nd, 2009, 20:14
|
#52 |
|
|
    Added MUR to the CASV as well.... |
|
|
|
|
February 27th, 2010, 02:01
|
#53 |
|
aka SNK or Shaniqua
|
Where did you get those mag pulls where the handle is sideways compared to the magpul made ones?
__________________
SHÖCK 
|
|
|
|
|
February 27th, 2010, 02:27
|
#54 |
|
|
same ones just installed differently....
|
|
|
|
|
February 27th, 2010, 03:24
|
#55 | |
![Shrapnel[Op-For]'s Avatar](/customavatars/avatar20401_9.gif){kind=avatar}
|
Quote:
|
|
|
|
|
|
February 27th, 2010, 03:58
|
#56 |
|
One word : gorgeous !
I especially like the CASV version with Aimpoint. Not planning to try with a tan lower ? I had a project like that with a tan Magpul lower and UBR.
__________________
Tous les jours nous nous endormons plus instruits mais pas forcément moins bêtes... I can do a CTRL+ATL+DEL on your gun ! Gun doc in Montreal on AEG, GBB, GBBR and Bolt rifle (gaz and spring) Heavy custom builder (including painting) 
|
|
|
|
|
February 27th, 2010, 04:13
|
#57 |
|
aka SNK or Shaniqua
|
How do you cut your ladder rails cleanly to custom size? The rubber always is hard to get a clean edge on it afterwards. Dremel and sand?
I have a green CASV (damnit, I'll need to powercoat it DE now because of this thread) but it has that opening in the front for the A-Frame. Is that a different CASV model that is solid across the top?
__________________
SHÖCK
|
|
|
|
|
February 27th, 2010, 09:07
|
#58 |
|
You have a CASV-EL, which was the first design from Vltor. The slot at the front of the frame is to accomodate the standard M4 front sight. What RM has is a CASV-M, which is slightly longer (mid-length) than the carbine or "extended length" of the EL version. It doesn't have the slot so on a carbine-length barrel, you'd have to use a low-profile gas block and some other rail-mounted or the flip-up front sight supplied with the CASV-M. Just go onto vltor.com and see the differences for yourself.
'Fly
__________________
 Team GHOSTS - Fides et Amicitia G-68 "Can't keep my eyes from the circling skies, Tongue-tied and twisted Just an earth-bound misfit, I" Learning To Fly © 1986 Pink Floyd |
|
|
|
  |
|
||||||
| Bookmarks |
|
|
 |
|
